Skip to main content
Electrolux | Help and Support

Tumble Dryers - Overview

  1. Last updated
  2. Save as PDF

 

There are three main types of the Household Tumble Dryers sold on the market:

Condense Dryer with Heat Pump Technology - Most efficient in terms of energy consumption.

2017-09-25_1332.png
  • Drying air is heated by the hot side of the heat pump.
  • Hot air passes through the load and causes water evaporation.
  • Water vapor is condensed by the cold side of the heat pump and collected into a reservoir or directly passed to the drain pipe.
  • The heat pump's hot side re-heats the air afterwards for reuse, which conserves much of the heat within the dryer.
  • A portion of the water vapor and heat leaks outside and increases the ambient temperature.
  • After some time air in the internal loop is warmer and more humid what can increase the drying time.
  • Heat re-circulation is the big advantage of this type of dryer, with a positive effect on energy consumption.

 

Condense Dryer with Heater


2017-09-25_1334.png
  • Drying air is heated by the heater.
  • hot air passes through the load and causes water evaporation.
  • Water vapor is condensed by the heat exchanger and collected into reservoir or directly passed to the drain pipe.
  • Heat exchanger is cooled by the forced stream of ambient air.
  • A portion of the water vapor and heat leaks outside and increases the ambient temperature.
  • After some time in operation air in the internal loop is warmer and more humid, which can increase drying time.

 

Exhaust Dryer with Heater

2017-09-25_1335.png
  • Drying air is heated by the heater.
  • Hot air passes through the load and causes water evaporation.
  • Hot air carrying water vapor is exhausted outside the room through the ventilation hose.
  • Heat is wasted, causing high energy consumption and hence high drying costs.
  • After some time air in the internal loop is more dry, decreasing drying time.

 

Tumble Dryers Comparison:
 

2017-09-25_1332.png

Condense Dryer with Heat Pump

2017-09-25_1334.png

Condense Dryer with Heater

2017-09-25_1335.png

Exhaust Dryer with Heater

energy consumption

 Image_014.png Image_015.png Image_016.png

drying temperatures

 Image_017.png Image_018.png Image_018.png

drying delicacy

 Image_020.pngImage_020.pngImage_020.png Image_020.png Image_020.png

drying cycle time

 Image_025.pngImage_025.pngImage_025.png Image_025.pngImage_025.png Image_025.png

energy saving*

 2017-09-25_1400.png2017-09-25_1400.png2017-09-25_1400.png 2017-09-25_1400.png

------

performance drying cost

 Image_036.pngImage_036.pngImage_036.png Image_036.png Image_036.png

* compared to exhaust dryers

Tumble Dryers - Hints and Tips of Effective Use:
Problem: Drying time shown on the display does not correspond to real drying time
  • This is because the cycle time on the display: Is shown before the drying starts and does not include real-time sensor measurements does not include some important drying conditions like: ambient temperature, initial laundry moisture, load mass and type is related to the average 5 kg loads of the cotton and jeans programs, and the respective recommended load of other programs.
Possible Cause and Solution
Image_043.png Possible Cause Image_044.png Possible Solution
Dryer installation was not place according to the installation requirements. Assure optimal installation place - Read carefully the installation requirements in user manual.
To low or to high ambient temperature below 5°C or higher than 35°C. Assure optimal room temperature  19°C - 24°C.
Too wet or even dripping laundry. Spin the laundry well before drying.
Laundry loads exceeds the recommended values. Use only proper loads.
Humidity sensor does not correct setting. Adjust remaining moisture laundry degree - See suitable procedure in user manual. (If you do not have your user manual, refer to Where can I find the user manual for my appliance?).